| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: fix ABBA deadlock in iptfs_destroy_state()
iptfs_destroy_state() calls hrtimer_cancel() while holding a spinlock
that the timer callback also acquires, leading to an ABBA deadlock on
SMP systems.
For the output timer (iptfs_timer):
- iptfs_destroy_state() holds x->lock, calls hrtimer_cancel()
- iptfs_delay_timer() callback takes x->lock
For the drop timer (drop_timer):
- iptfs_destroy_state() holds drop_lock, calls hrtimer_cancel()
- iptfs_drop_timer() callback takes drop_lock
Both timers use HRTIMER_MODE_REL_SOFT, so their callbacks run in softirq
context. When hrtimer_cancel() is called for a soft timer that is
currently executing on another CPU, hrtimer_cancel_wait_running() spins
on softirq_expiry_lock -- the same lock held by the softirq running the
callback. If the callback is blocked waiting for the spinlock held by
the caller of hrtimer_cancel(), a circular dependency forms:
CPU 0: holds lock_A -> waits for softirq_expiry_lock
CPU 1: holds softirq_expiry_lock -> waits for lock_A
Fix by calling hrtimer_cancel() before acquiring the respective locks.
hrtimer_cancel() is safe to call without holding any lock and will wait
for any in-progress callback to complete. For the output timer, the
lock is still acquired afterwards to drain the packet queue. For the
drop timer, the lock/unlock pair is removed entirely since it only
existed to serialize with the timer callback, which hrtimer_cancel()
already guarantees.
Found by source code audit. |
| In the Linux kernel, the following vulnerability has been resolved:
greybus: gb-beagleplay: fix sleep in atomic context in hdlc_tx_frames()
hdlc_append() calls usleep_range() to wait for circular buffer space,
but it is called with tx_producer_lock (a spinlock) held via
hdlc_tx_frames() -> hdlc_append_tx_frame()/hdlc_append_tx_u8()/etc.
Sleeping while holding a spinlock is illegal and can trigger
"BUG: scheduling while atomic".
Fix this by moving the buffer-space wait out of hdlc_append() and into
hdlc_tx_frames(), before the spinlock is acquired. The new flow:
1. Pre-calculate the worst-case encoded frame length.
2. Wait (with sleep) outside the lock until enough space is available,
kicking the TX consumer work to drain the buffer.
3. Acquire the spinlock, re-verify space, and write the entire frame
atomically.
This ensures that sleeping only happens without any lock held, and
that frames are either fully enqueued or not written at all.
This bug is found by CodeQL static analysis tool (interprocedural
sleep-in-atomic query) and my code review. |
| ASP.NET Core and Visual Studio Denial of Service Vulnerability |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: fix deadlock in jbd2_journal_cancel_revoke()
Commit f76d4c28a46a ("fs/jbd2: use sleeping version of
__find_get_block()") changed jbd2_journal_cancel_revoke() to use
__find_get_block_nonatomic() which holds the folio lock instead of
i_private_lock. This breaks the lock ordering (folio -> buffer) and
causes an ABBA deadlock when the filesystem blocksize < pagesize:
T1 T2
ext4_mkdir()
ext4_init_new_dir()
ext4_append()
ext4_getblk()
lock_buffer() <- A
sync_blockdev()
blkdev_writepages()
writeback_iter()
writeback_get_folio()
folio_lock() <- B
ext4_journal_get_create_access()
jbd2_journal_cancel_revoke()
__find_get_block_nonatomic()
folio_lock() <- B
block_write_full_folio()
lock_buffer() <- A
This can occasionally cause generic/013 to hang.
Fix by only calling __find_get_block_nonatomic() when the passed
buffer_head doesn't belong to the bdev, which is the only case that we
need to look up its bdev alias. Otherwise, the lookup is redundant since
the found buffer_head is equal to the one we passed in. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup: Defer css percpu_ref kill on rmdir until cgroup is depopulated
A chain of commits going back to v7.0 reworked rmdir to satisfy the
controller invariant that a subsystem's ->css_offline() must not run while
tasks are still doing kernel-side work in the cgroup.
[1] d245698d727a ("cgroup: Defer task cgroup unlink until after the task is done switching out")
[2] a72f73c4dd9b ("cgroup: Don't expose dead tasks in cgroup")
[3] 1b164b876c36 ("cgroup: Wait for dying tasks to leave on rmdir")
[4] 4c56a8ac6869 ("cgroup: Fix cgroup_drain_dying() testing the wrong condition")
[5] 13e786b64bd3 ("cgroup: Increment nr_dying_subsys_* from rmdir context")
[1] moved task cset unlink from do_exit() to finish_task_switch() so a
task's cset link drops only after the task has fully stopped scheduling.
That made tasks past exit_signals() linger on cset->tasks until their final
context switch, which led to a series of problems as what userspace expected
to see after rmdir diverged from what the kernel needs to wait for. [2]-[5]
tried to bridge that divergence: [2] filtered the exiting tasks from
cgroup.procs; [3] had rmdir(2) sleep in TASK_UNINTERRUPTIBLE for them; [4]
fixed the wait's condition; [5] made nr_dying_subsys_* visible
synchronously.
The cgroup_drain_dying() wait in [3] turned out to be a dead end. When the
rmdir caller is also the reaper of a zombie that pins a pidns teardown (e.g.
host PID 1 systemd reaping orphan pids that were re-parented to it during
the same teardown), rmdir blocks in TASK_UNINTERRUPTIBLE waiting for those
pids to free, the pids can't free because PID 1 is the reaper and it's stuck
in rmdir, and the system A-A deadlocks. No internal lock ordering breaks
this; the wait itself is the bug.
The css killing side that drove the original reorder, however, can be made
cleanly asynchronous: ->css_offline() is already async, run from
css_killed_work_fn() driven by percpu_ref_kill_and_confirm(). The fix is to
make that chain start only after all tasks have left the cgroup. rmdir's
user-visible side then returns as soon as cgroup.procs and friends are
empty, while ->css_offline() still runs only after the cgroup is fully
drained.
Verified by the original reproducer (pidns teardown + zombie reaper, runs
under vng) which hangs vanilla and succeeds here, and by per-commit
deterministic repros for [2], [3], [4], [5] with a boot parameter that
widens the post-exit_signals() window so each state is reliably reachable.
Some stress tests on top of that.
cgroup_apply_control_disable() has the same shape of pre-existing race:
when a controller is disabled via subtree_control, kill_css() ran
synchronously while tasks past exit_signals() could still be linked to
the cgroup's csets, and ->css_offline() could fire before they drained.
This patch preserves the existing synchronous behavior at that call site
(kill_css_sync() + kill_css_finish() back-to-back) and a follow-up patch
will defer kill_css_finish() there using a per-css trigger.
This seems like the right approach and I don't see problems with it. The
changes are somewhat invasive but not excessively so, so backporting to
-stable should be okay. If something does turn out to be wrong, the fallback
is to revert the entire chain ([1]-[5]) and rework in the development branch
instead.
v2: Pin cgrp across the deferred destroy work with explicit
cgroup_get()/cgroup_put() around queue_work() and the work_fn. v1
wasn't actually broken (ordered cgroup_offline_wq + queue_work order
in cgroup_task_dead() saved it) but the explicit ref removes the
dependency on those non-obvious invariants. Also note the
pre-existing cgroup_apply_control_disable() race in the description;
a follow-up will defer kill_css_finish() there. |
| Ubuntu Linux 6.8, 6.17 and 7.0 contain AppArmor SAUCE patches which incorrectly sleep while holding a spinlock in notification handling code. The bug can be triggered by an unprivileged local user and can result in kernel panic or deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix deadlocks between devlink and netdev instance locks
In the mentioned "Fixes" commit, various work tasks triggering devlink
health reporter recovery were switched to use netdev_trylock to protect
against concurrent tear down of the channels being recovered. But this
had the side effect of introducing potential deadlocks because of
incorrect lock ordering.
The correct lock order is described by the init flow:
probe_one -> mlx5_init_one (acquires devlink lock)
-> mlx5_init_one_devl_locked -> mlx5_register_device
-> mlx5_rescan_drivers_locked -...-> mlx5e_probe -> _mlx5e_probe
-> register_netdev (acquires rtnl lock)
-> register_netdevice (acquires netdev lock)
=> devlink lock -> rtnl lock -> netdev lock.
But in the current recovery flow, the order is wrong:
mlx5e_tx_err_cqe_work (acquires netdev lock)
-> mlx5e_reporter_tx_err_cqe -> mlx5e_health_report
-> devlink_health_report (acquires devlink lock => boom!)
-> devlink_health_reporter_recover
-> mlx5e_tx_reporter_recover -> mlx5e_tx_reporter_recover_from_ctx
-> mlx5e_tx_reporter_err_cqe_recover
The same pattern exists in:
mlx5e_reporter_rx_timeout
mlx5e_reporter_tx_ptpsq_unhealthy
mlx5e_reporter_tx_timeout
Fix these by moving the netdev_trylock calls from the work handlers
lower in the call stack, in the respective recovery functions, where
they are actually necessary. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: fix deadlock in ni_read_folio_cmpr
Syzbot reported a task hung in ni_readpage_cmpr (now ni_read_folio_cmpr).
This is caused by a lock inversion deadlock involving the inode mutex
(ni_lock) and page locks.
Scenario:
1. Task A enters ntfs_read_folio() for page X. It acquires ni_lock.
2. Task A calls ni_read_folio_cmpr(), which attempts to lock all pages in
the compressed frame (including page Y).
3. Concurrently, Task B (e.g., via readahead) has locked page Y and
calls ntfs_read_folio().
4. Task B waits for ni_lock (held by A).
5. Task A waits for page Y lock (held by B).
-> DEADLOCK.
The fix is to restructure locking: do not take ni_lock in ntfs_read_folio().
Instead, acquire ni_lock inside ni_read_folio_cmpr() ONLY AFTER all required
page locks for the frame have been successfully acquired. This restores the
correct lock ordering (Page Lock -> ni_lock) consistent with VFS.
[almaz.alexandrovich@paragon-software.com: ni_readpage_cmpr was renamed to ni_read_folio_cmpr] |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: Avoid double-rtnl_lock ELP metric worker
batadv_v_elp_get_throughput() might be called when the RTNL lock is already
held. This could be problematic when the work queue item is cancelled via
cancel_delayed_work_sync() in batadv_v_elp_iface_disable(). In this case,
an rtnl_lock() would cause a deadlock.
To avoid this, rtnl_trylock() was used in this function to skip the
retrieval of the ethtool information in case the RTNL lock was already
held.
But for cfg80211 interfaces, batadv_get_real_netdev() was called - which
also uses rtnl_lock(). The approach for __ethtool_get_link_ksettings() must
also be used instead and the lockless version __batadv_get_real_netdev()
has to be called. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/imagination: Fix deadlock in soft reset sequence
The soft reset sequence is currently executed from the threaded IRQ
handler, hence it cannot call disable_irq() which internally waits
for IRQ handlers, i.e. itself, to complete.
Use disable_irq_nosync() during a soft reset instead. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix SCX_KICK_WAIT deadlock by deferring wait to balance callback
SCX_KICK_WAIT busy-waits in kick_cpus_irq_workfn() using
smp_cond_load_acquire() until the target CPU's kick_sync advances. Because
the irq_work runs in hardirq context, the waiting CPU cannot reschedule and
its own kick_sync never advances. If multiple CPUs form a wait cycle, all
CPUs deadlock.
Replace the busy-wait in kick_cpus_irq_workfn() with resched_curr() to
force the CPU through do_pick_task_scx(), which queues a balance callback
to perform the wait. The balance callback drops the rq lock and enables
IRQs following the sched_core_balance() pattern, so the CPU can process
IPIs while waiting. The local CPU's kick_sync is advanced on entry to
do_pick_task_scx() and continuously during the wait, ensuring any CPU that
starts waiting for us sees the advancement and cannot form cyclic
dependencies. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: Workaround SQM/PSE stalls by disabling sticky
NIX SQ manager sticky mode is known to cause stalls when multiple SQs
share an SMQ and transmit concurrently. Additionally, PSE may deadlock
on transitions between sticky and non-sticky transmissions. There is
also a credit drop issue observed when certain condition clocks are
gated.
work around these hardware errata by:
- Disabling SQM sticky operation:
- Clear TM6 (bit 15)
- Clear TM11 (bit 14)
- Disabling sticky → non-sticky transition path that can deadlock PSE:
- Clear TM5 (bit 23)
- Preventing credit drops by keeping the control-flow clock enabled:
- Set TM9 (bit 21)
These changes are applied via NIX_AF_SQM_DBG_CTL_STATUS. With this
configuration the SQM/PSE maintain forward progress under load without
credit loss, at the cost of disabling sticky optimizations. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/slab: do not access current->mems_allowed_seq if !allow_spin
Lockdep complains when get_from_any_partial() is called in an NMI
context, because current->mems_allowed_seq is seqcount_spinlock_t and
not NMI-safe:
================================
WARNING: inconsistent lock state
6.19.0-rc5-kfree-rcu+ #315 Tainted: G N
--------------------------------
inconsistent {INITIAL USE} -> {IN-NMI} usage.
kunit_try_catch/9989 [HC1[1]:SC0[0]:HE0:SE1] takes:
ffff889085799820 (&____s->seqcount#3){.-.-}-{0:0}, at: ___slab_alloc+0x58f/0xc00
{INITIAL USE} state was registered at:
lock_acquire+0x185/0x320
kernel_init_freeable+0x391/0x1150
kernel_init+0x1f/0x220
ret_from_fork+0x736/0x8f0
ret_from_fork_asm+0x1a/0x30
irq event stamp: 56
hardirqs last enabled at (55): [<ffffffff850a68d7>] _raw_spin_unlock_irq+0x27/0x70
hardirqs last disabled at (56): [<ffffffff850858ca>] __schedule+0x2a8a/0x6630
softirqs last enabled at (0): [<ffffffff81536711>] copy_process+0x1dc1/0x6a10
softirqs last disabled at (0): [<0000000000000000>] 0x0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&____s->seqcount#3);
<Interrupt>
lock(&____s->seqcount#3);
*** DEADLOCK ***
According to Documentation/locking/seqlock.rst, seqcount_t is not
NMI-safe and seqcount_latch_t should be used when read path can interrupt
the write-side critical section. In this case, do not access
current->mems_allowed_seq and avoid retry. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: fix deadlock in create_pinctrl() when handling -EPROBE_DEFER
In create_pinctrl(), pinctrl_maps_mutex is acquired before calling
add_setting(). If add_setting() returns -EPROBE_DEFER, create_pinctrl()
calls pinctrl_free(). However, pinctrl_free() attempts to acquire
pinctrl_maps_mutex, which is already held by create_pinctrl(), leading to
a potential deadlock.
This patch resolves the issue by releasing pinctrl_maps_mutex before
calling pinctrl_free(), preventing the deadlock.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_api: fix possible infinite loop in tcf_idr_check_alloc()
syzbot found hanging tasks waiting on rtnl_lock [1]
A reproducer is available in the syzbot bug.
When a request to add multiple actions with the same index is sent, the
second request will block forever on the first request. This holds
rtnl_lock, and causes tasks to hang.
Return -EAGAIN to prevent infinite looping, while keeping documented
behavior.
[1]
INFO: task kworker/1:0:5088 blocked for more than 143 seconds.
Not tainted 6.9.0-rc4-syzkaller-00173-g3cdb45594619 #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/1:0 state:D stack:23744 pid:5088 tgid:5088 ppid:2 flags:0x00004000
Workqueue: events_power_efficient reg_check_chans_work
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5409 [inline]
__schedule+0xf15/0x5d00 kernel/sched/core.c:6746
__schedule_loop kernel/sched/core.c:6823 [inline]
schedule+0xe7/0x350 kernel/sched/core.c:6838
schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:6895
__mutex_lock_common kernel/locking/mutex.c:684 [inline]
__mutex_lock+0x5b8/0x9c0 kernel/locking/mutex.c:752
wiphy_lock include/net/cfg80211.h:5953 [inline]
reg_leave_invalid_chans net/wireless/reg.c:2466 [inline]
reg_check_chans_work+0x10a/0x10e0 net/wireless/reg.c:2481 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: Fix deadlock in ieee80211_sta_ps_deliver_wakeup()
The ieee80211_sta_ps_deliver_wakeup() function takes sta->ps_lock to
synchronizes with ieee80211_tx_h_unicast_ps_buf() which is called from
softirq context. However using only spin_lock() to get sta->ps_lock in
ieee80211_sta_ps_deliver_wakeup() does not prevent softirq to execute
on this same CPU, to run ieee80211_tx_h_unicast_ps_buf() and try to
take this same lock ending in deadlock. Below is an example of rcu stall
that arises in such situation.
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 2-....: (42413413 ticks this GP) idle=b154/1/0x4000000000000000 softirq=1763/1765 fqs=21206996
rcu: (t=42586894 jiffies g=2057 q=362405 ncpus=4)
CPU: 2 PID: 719 Comm: wpa_supplicant Tainted: G W 6.4.0-02158-g1b062f552873 #742
Hardware name: RPT (r1) (DT)
pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : queued_spin_lock_slowpath+0x58/0x2d0
lr : invoke_tx_handlers_early+0x5b4/0x5c0
sp : ffff00001ef64660
x29: ffff00001ef64660 x28: ffff000009bc1070 x27: ffff000009bc0ad8
x26: ffff000009bc0900 x25: ffff00001ef647a8 x24: 0000000000000000
x23: ffff000009bc0900 x22: ffff000009bc0900 x21: ffff00000ac0e000
x20: ffff00000a279e00 x19: ffff00001ef646e8 x18: 0000000000000000
x17: ffff800016468000 x16: ffff00001ef608c0 x15: 0010533c93f64f80
x14: 0010395c9faa3946 x13: 0000000000000000 x12: 00000000fa83b2da
x11: 000000012edeceea x10: ffff0000010fbe00 x9 : 0000000000895440
x8 : 000000000010533c x7 : ffff00000ad8b740 x6 : ffff00000c350880
x5 : 0000000000000007 x4 : 0000000000000001 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 0000000000000001 x0 : ffff00000ac0e0e8
Call trace:
queued_spin_lock_slowpath+0x58/0x2d0
ieee80211_tx+0x80/0x12c
ieee80211_tx_pending+0x110/0x278
tasklet_action_common.constprop.0+0x10c/0x144
tasklet_action+0x20/0x28
_stext+0x11c/0x284
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
do_softirq+0x74/0x7c
__local_bh_enable_ip+0xa0/0xa4
_ieee80211_wake_txqs+0x3b0/0x4b8
__ieee80211_wake_queue+0x12c/0x168
ieee80211_add_pending_skbs+0xec/0x138
ieee80211_sta_ps_deliver_wakeup+0x2a4/0x480
ieee80211_mps_sta_status_update.part.0+0xd8/0x11c
ieee80211_mps_sta_status_update+0x18/0x24
sta_apply_parameters+0x3bc/0x4c0
ieee80211_change_station+0x1b8/0x2dc
nl80211_set_station+0x444/0x49c
genl_family_rcv_msg_doit.isra.0+0xa4/0xfc
genl_rcv_msg+0x1b0/0x244
netlink_rcv_skb+0x38/0x10c
genl_rcv+0x34/0x48
netlink_unicast+0x254/0x2bc
netlink_sendmsg+0x190/0x3b4
____sys_sendmsg+0x1e8/0x218
___sys_sendmsg+0x68/0x8c
__sys_sendmsg+0x44/0x84
__arm64_sys_sendmsg+0x20/0x28
do_el0_svc+0x6c/0xe8
el0_svc+0x14/0x48
el0t_64_sync_handler+0xb0/0xb4
el0t_64_sync+0x14c/0x150
Using spin_lock_bh()/spin_unlock_bh() instead prevents softirq to raise
on the same CPU that is holding the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
media: usbtv: Remove useless locks in usbtv_video_free()
Remove locks calls in usbtv_video_free() because
are useless and may led to a deadlock as reported here:
https://syzkaller.appspot.com/x/bisect.txt?x=166dc872180000
Also remove usbtv_stop() call since it will be called when
unregistering the device.
Before 'c838530d230b' this issue would only be noticed if you
disconnect while streaming and now it is noticeable even when
disconnecting while not streaming.
[hverkuil: fix minor spelling mistake in log message] |
| In the Linux kernel, the following vulnerability has been resolved:
writeback: don't block sync for filesystems with no data integrity guarantees
Add a SB_I_NO_DATA_INTEGRITY superblock flag for filesystems that cannot
guarantee data persistence on sync (eg fuse). For superblocks with this
flag set, sync kicks off writeback of dirty inodes but does not wait
for the flusher threads to complete the writeback.
This replaces the per-inode AS_NO_DATA_INTEGRITY mapping flag added in
commit f9a49aa302a0 ("fs/writeback: skip AS_NO_DATA_INTEGRITY mappings
in wait_sb_inodes()"). The flag belongs at the superblock level because
data integrity is a filesystem-wide property, not a per-inode one.
Having this flag at the superblock level also allows us to skip having
to iterate every dirty inode in wait_sb_inodes() only to skip each inode
individually.
Prior to this commit, mappings with no data integrity guarantees skipped
waiting on writeback completion but still waited on the flusher threads
to finish initiating the writeback. Waiting on the flusher threads is
unnecessary. This commit kicks off writeback but does not wait on the
flusher threads. This change properly addresses a recent report [1] for
a suspend-to-RAM hang seen on fuse-overlayfs that was caused by waiting
on the flusher threads to finish:
Workqueue: pm_fs_sync pm_fs_sync_work_fn
Call Trace:
<TASK>
__schedule+0x457/0x1720
schedule+0x27/0xd0
wb_wait_for_completion+0x97/0xe0
sync_inodes_sb+0xf8/0x2e0
__iterate_supers+0xdc/0x160
ksys_sync+0x43/0xb0
pm_fs_sync_work_fn+0x17/0xa0
process_one_work+0x193/0x350
worker_thread+0x1a1/0x310
kthread+0xfc/0x240
ret_from_fork+0x243/0x280
ret_from_fork_asm+0x1a/0x30
</TASK>
On fuse this is problematic because there are paths that may cause the
flusher thread to block (eg if systemd freezes the user session cgroups
first, which freezes the fuse daemon, before invoking the kernel
suspend. The kernel suspend triggers ->write_node() which on fuse issues
a synchronous setattr request, which cannot be processed since the
daemon is frozen. Or if the daemon is buggy and cannot properly complete
writeback, initiating writeback on a dirty folio already under writeback
leads to writeback_get_folio() -> folio_prepare_writeback() ->
unconditional wait on writeback to finish, which will cause a hang).
This commit restores fuse to its prior behavior before tmp folios were
removed, where sync was essentially a no-op.
[1] https://lore.kernel.org/linux-fsdevel/CAJnrk1a-asuvfrbKXbEwwDSctvemF+6zfhdnuzO65Pt8HsFSRw@mail.gmail.com/T/#m632c4648e9cafc4239299887109ebd880ac6c5c1 |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: omap: do not register driver in probe()
Commit 11a78b794496 ("ARM: OMAP: MPUIO wake updates") registers the
omap_mpuio_driver from omap_mpuio_init(), which is called from
omap_gpio_probe().
However, it neither makes sense to register drivers from probe()
callbacks of other drivers, nor does the driver core allow registering
drivers with a device lock already being held.
The latter was revealed by commit dc23806a7c47 ("driver core: enforce
device_lock for driver_match_device()") leading to a potential deadlock
condition described in [1].
Additionally, the omap_mpuio_driver is never unregistered from the
driver core, even if the module is unloaded.
Hence, register the omap_mpuio_driver from the module initcall and
unregister it in module_exit(). |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: nci: fix circular locking dependency in nci_close_device
nci_close_device() flushes rx_wq and tx_wq while holding req_lock.
This causes a circular locking dependency because nci_rx_work()
running on rx_wq can end up taking req_lock too:
nci_rx_work -> nci_rx_data_packet -> nci_data_exchange_complete
-> __sk_destruct -> rawsock_destruct -> nfc_deactivate_target
-> nci_deactivate_target -> nci_request -> mutex_lock(&ndev->req_lock)
Move the flush of rx_wq after req_lock has been released.
This should safe (I think) because NCI_UP has already been cleared
and the transport is closed, so the work will see it and return
-ENETDOWN.
NIPA has been hitting this running the nci selftest with a debug
kernel on roughly 4% of the runs. |