| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad_sigma_delta: fix CS held asserted and state leaks
In ad_sigma_delta_single_conversion(), set_mode(AD_SD_MODE_IDLE) and
disable_one() were called from the out: block while keep_cs_asserted
was still true. This caused any SPI transfer issued by those callbacks
to carry cs_change=1, leaving CS permanently asserted after the
conversion. Fix by moving both calls into the out_unlock: block, after
keep_cs_asserted is cleared, matching the pattern already used in
ad_sd_calibrate().
In the error path of ad_sd_buffer_postenable(), if an operation fails
after set_mode(AD_SD_MODE_CONTINUOUS) has already succeeded (e.g.
spi_offload_trigger_enable()), the device is left in continuous
conversion mode with CS physically asserted. Additionally,
bus_locked remaining true after spi_bus_unlock() causes subsequent
SPI operations to call spi_sync_locked() without the bus lock actually
held, allowing concurrent SPI access.
Fix the error path by clearing keep_cs_asserted first, then calling
set_mode(AD_SD_MODE_IDLE) to revert the device mode and deassert CS,
then clearing bus_locked before releasing the bus.
For devices that implement neither set_mode nor disable_one (such as
MAX11205, which has no physical CS pin), no SPI transfer is issued
during cleanup and the cs_change flag has no effect on any physical
line. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad_sigma_delta: fix clear_pending_event for registerless devices
ad_sigma_delta_clear_pending_event() falls through to the status register
read path for devices with has_registers = false and no rdy_gpiod. For
such devices, ad_sd_read_reg() skips the address byte entirely and clocks
raw MISO bytes with no address phase — making it byte-for-byte identical
to reading conversion data. If a pending conversion result is present,
this partially consumes it and corrupts the data stream for the subsequent
ad_sd_read_reg() call in ad_sigma_delta_single_conversion().
Furthermore, with num_resetclks = 0 on these devices, data_read_len
evaluates to 0. If the clocked byte has bit 7 clear, pending_event is set
and the code attempts memset(data + 2, 0xff, 0 - 1), overflowing to
SIZE_MAX and corrupting the heap.
Fix by returning 0 immediately when neither rdy_gpiod nor has_registers
is set. This is safe for all current registerless devices: ad7191 and
ad7780 (with powerdown GPIO) are reset between conversions by CS
deassertion, so there is no stale result to drain; ad7780 (without
powerdown GPIO) and max11205 are continuously-converting and cycle ~DRDY
at the output data rate regardless of whether the previous result was
read, so the next falling edge fires naturally.
A future registerless device that holds ~DRDY asserted until data is read
would be broken by this early return and would require either
num_resetclks set or a rdy-gpio.
The same heap corruption is reachable on any device with rdy_gpiod set
but num_resetclks = 0: if the GPIO indicates a pending event, the drain
path executes memset(data + 2, 0xff, 0 - 1) regardless of has_registers.
Add an explicit data_read_len == 0 guard after the pending event check;
the stale result is then consumed by the first ad_sd_read_reg() call in
ad_sigma_delta_single_conversion(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kxsd9: fix runtime PM imbalance on write_raw() error
kxsd9_write_raw() takes a runtime PM reference with pm_runtime_get_sync()
but returns -EINVAL directly when a scale with a non-zero integer part is
requested, skipping the matching pm_runtime_put_autosuspend(). This leaks
a runtime PM usage-counter reference on every such write, after which the
device can no longer autosuspend.
Set the error code and fall through to the existing put instead of
returning early. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: CPPC: Suppress UBSAN warning caused by field misuse
The definition of reg->access_width changes depending on the
reg->space_id type. Type ACPI_ADR_SPACE_PLATFORM_COMM uses
access_width to indicate the PCC region, which can result in a UBSAN
if the value is greater than 4.
For example:
UBSAN: shift-out-of-bounds in drivers/acpi/cppc_acpi.c:1090:9
shift exponent 32 is too large for 32-bit type 'int'
CPU: 61 UID: 0 PID: 1220 Comm: (udev-worker) Not tainted 7.0.10-201.fc44.aarch64 #1 PREEMPT(lazy)
Hardware name: To be filled by O.E.M.
Call trace:
...(trimming)
ubsan_epilogue+0x10/0x48
__ubsan_handle_shift_out_of_bounds+0xdc/0x1e0
cpc_write+0x4d0/0x670
cppc_set_perf+0x18c/0x490
cppc_cpufreq_cpu_init+0x1c8/0x380 [cppc_cpufreq]
... (trimming)
Lets fix this by validating the region type, as well as whether
access_width has a value. Then since we are returning bit_width
directly for ACPI_ADR_SPACE_PLATFORM_COMM, drop the code correcting
the size. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Unconditionally recompute CR8 intercept on PPR update
The TPR_THRESHOLD field in the VMCS is used by VMX to induce VM exits
when the guest's virtual TPR falls under the specified threshold,
allowing KVM to inject previously masked interrupts.
KVM handles these VM exits in handle_tpr_below_threshold().
Commit eb90f3417a0c ("KVM: vmx: speed up TPR below threshold vmexits")
optimized this function by calling apic_update_ppr() instead of raising
KVM_REQ_EVENT. apic_update_ppr() then raises KVM_REQ_EVENT if there is
a pending, deliverable interrupt.
However, if there are no new interrupts pending, apic_update_ppr() does
not issue the request. Thus, kvm_lapic_update_cr8_intercept() and
vmx_update_cr8_intercept() are not called before VM entry, which results
in a high, stale TPR_THRESHOLD. This is problematic due to the following
sentence in 28.2.1.1 "VM-Execution Control Fields" in the SDM:
The following check is performed if the “use TPR shadow” VM-execution
control is 1 and the “virtualize APIC accesses” and “virtual-interrupt
delivery” VM-execution controls are both 0: the value of bits 3:0 of
the TPR threshold VM-execution control field should not be greater
than the value of bits 7:4 of VTPR.
This error condition is typically not observed when KVM runs on a bare
metal system because modern processors support APICv, which enables
virtual-interrupt delivery, and which KVM uses when possible. This
causes the processor to no longer generate TPR-below-threshold exits
and to no longer check TPR_THRESHOLD on entry. However, when running
on older platforms, or under nested virtualization on a hypervisor that
does not support virtual-interrupt delivery and enforces this check
(like Hyper-V) this can cause a VM entry failure with hardware error
0x7, as seen in [1].
Call kvm_lapic_update_cr8_intercept() if apic_update_ppr() does not
find a deliverable interrupt (and thus does not raise KVM_REQ_EVENT).
Remove calls to kvm_lapic_update_cr8_intercept() on paths that end up in
apic_update_ppr(), as they now become redundant. This ensures that any
path that updates the guest's PPR also figures out if KVM needs to wait
for a TPR change (using TPR_THRESHOLD on VMX or CR8 intercepts on SVM). |
| In the Linux kernel, the following vulnerability has been resolved:
userfaultfd: gate must_wait writability check on pte_present()
userfaultfd_must_wait() and userfaultfd_huge_must_wait() read the PTE
without taking the page table lock and then apply pte_write() /
huge_pte_write() to it. Those accessors decode bits from the present
encoding only; on a swap or migration entry they read the offset bits that
happen to share the same position and return an undefined result.
The intent of the check is "is this fault still WP-blocked?". A
non-marker swap entry means the page is in transit -- the userfault
context the original fault delivered against is no longer the same, and
the swap-in or migration completion path will re-deliver a fresh fault if
userspace still needs to handle it. Worst case under the current code the
garbage write bit says "wait", and the thread stays asleep until a
UFFDIO_WAKE that may never arrive.
Gate the writability check on pte_present() so the lockless re-check only
inspects present-PTE bits when the entry is actually present. The
non-present, non-marker case returns "don't wait" and lets the fault path
retry. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vce1: Fix VCE 1 firmware size and offsets
The VCPU BO contains the actual FW at an offset, but
it was not calculated into the VCPU BO size.
Subtract this from the FW size to make sure there is
no out of bounds access.
Make sure the stack and data offsets are aligned to
the 32K TLB size.
Check that the FW microcode actually fits in the
space that is reserved for it.
(cherry picked from commit c16fe59f622a080fc457a57b3e8f14c780699449) |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: use wq_has_sleeper() in release_in_xmit()
release_in_xmit() clears RDS_IN_XMIT with clear_bit_unlock() and then
checks waitqueue_active() to decide whether anyone needs waking.
clear_bit_unlock() is only a release operation: it orders the
critical section before the bit clear, but does not order the
subsequent plain load of the wait queue head after it. The waiter
side does the mirror image - it adds itself to the wait queue and
then tests the bit. That is the classic store-buffering pattern: the
releasing CPU can read the wait queue as empty while the waiting CPU
still reads the bit as set, so the sleeper is never woken.
The waiters are rds_conn_shutdown() and rds_tcp_reset_callbacks(),
both in uninterruptible wait_event() with no timeout. A lost wake-up
strands the shutdown worker on its single-threaded workqueue until
some other sender releases the bit again - and on a connection that
is being torn down precisely because it failed, there may never be
another sender.
The barrier used to be there: release_in_xmit() did clear_bit()
followed by smp_mb__after_atomic() until commit 1422f28826d2 ("rds:
introduce acquire/release ordering in acquire/release_in_xmit()")
folded both into clear_bit_unlock(), which strengthened the lock
hand-off but silently dropped the full barrier the wake-up check
depends on. The refill counterpart, release_refill() in
net/rds/ib_recv.c, still carries its smp_mb__after_atomic() for
exactly this reason.
Use wq_has_sleeper(), which is waitqueue_active() preceded by the
required full barrier. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: Fix null-ptr-deref in fib6_nh_mtu_change().
fib6_nh_mtu_change() re-fetches idev via __in6_dev_get(arg->dev) and
dereferences idev->cnf.mtu6 without a NULL check. addrconf_ifdown()
clears dev->ip6_ptr with RCU_INIT_POINTER() after rt6_disable_ip() has
released tb6_lock, so the RA-driven MTU walk can observe a NULL idev and
oops. The caller rt6_mtu_change_route() guards its own __in6_dev_get(),
but this re-fetch is unguarded; nexthop-backed routes survive
addrconf_ifdown()'s flush, so the walk still reaches it after ip6_ptr is
nulled.
Return 0 when idev is NULL, matching rt6_mtu_change_route() and the
fib6_mtu() fix in commit 5ad509c1fdad ("ipv6: Fix null-ptr-deref in
fib6_mtu().").
Oops: general protection fault, ... KASAN: null-ptr-deref in range
[0x00000000000002a8-0x00000000000002af]
RIP: 0010:fib6_nh_mtu_change+0x203/0x990
rt6_mtu_change_route+0x141/0x1d0
__fib6_clean_all+0xd0/0x160
rt6_mtu_change+0xb4/0x100
ndisc_router_discovery+0x24b5/0x2cb0
icmpv6_rcv+0x12e9/0x1710
ipv6_rcv+0x39b/0x410 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject resilient lock operations in rbtree callbacks
__bpf_rbtree_add() keeps parent and link pointers live across calls to the
program-supplied comparison callback. The verifier therefore requires the
root's lock to remain held throughout the callback.
The helper path enforces this rule for bpf_spin_lock() and
bpf_spin_unlock(), but the resilient lock kfunc argument path does not.
Since resilient locks may protect BPF rbtree roots, a callback can release
the root lock and let another CPU remove and free the node referenced by
the in-progress tree walk. The walk then resumes using freed pointers.
Reject resilient lock kfuncs in an rbtree comparison callback, matching
the existing policy for the spin lock helpers. Resilient-lock-protected
trees remain valid when their comparison callbacks leave lock state alone. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject tail calls directly from callback frames
A tail call from a non-zero frame is modeled as a return from that frame.
The verifier makes R0 unknown and calls prepare_func_exit() for the taken
branch.
When the current frame is a synchronous callback, prepare_func_exit()
enforces the callback return-value contract and marks R0 precise. Since the
tail-call path synthesized R0 rather than deriving it from an instruction,
precision backtracking reaches the callback-calling instruction with R0
still requested and triggers the "callback unexpected regs" verifier bug.
A CAP_BPF task can therefore cause a WARN and an -EFAULT BPF_PROG_LOAD.
Tail calls reachable from callbacks are already rejected later by
check_max_stack_depth(). Reject a tail call made directly by a callback
before constructing the inconsistent return state, using the existing
diagnostic. Tail calls from ordinary subprograms keep their current
behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix NULL-ptr-deref in btf_var_show()
btf_var_show() calls btf_type_id_resolve() unconditionally, which
dereferences btf->resolved_ids. That is NULL for a base BTF - e.g. the
vmlinux BTF that bpf_snprintf_btf() renders against - since base BTF is
not resolved during parsing. btf_modifier_show() guards this with
'if (btf->resolved_ids)', but btf_var_show() does not.
A BPF program that passes the type_id of a BTF_KIND_VAR from the vmlinux
BTF to bpf_snprintf_btf() thus NULL-derefs:
KASAN: probably user-memory-access in range [0x46638-0x4663f]
RIP: 0010:btf_var_show (kernel/bpf/btf.c:2929)
Call Trace:
<TASK>
btf_type_show (kernel/bpf/btf.c:8259)
btf_type_snprintf_show (kernel/bpf/btf.c:8329)
bpf_snprintf_btf (kernel/trace/bpf_trace.c:1047)
bpf_prog_test_run_raw_tp (net/bpf/test_run.c:829)
__sys_bpf (kernel/bpf/syscall.c:4804)
do_syscall_64 (arch/x86/entry/syscall_64.c:84)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
</TASK>
Resolve the var's type directly with btf_type_skip_modifiers() when
resolved_ids is NULL, mirroring btf_modifier_show(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix NULL-ptr-deref when showing a void BTF type
btf_modifier_show() resolves the modifier and then calls
btf_type_ops(t)->show() unconditionally. For the void type (type_id 0,
BTF_KIND_UNKN) kind_ops[] has no entry, so ->show is NULL.
A "const void" (a modifier resolving to void) cannot be a map key or
value - map_check_btf() rejects it because void has no size - so the map
dump path does not reach it. But bpf_snprintf_btf() takes a type_id
straight from the BPF program, and passing such a "const void" from the
vmlinux BTF NULL-derefs:
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
RIP: 0010:btf_modifier_show (kernel/bpf/btf.c:2914)
Call Trace:
<TASK>
btf_type_show (kernel/bpf/btf.c:8251)
btf_type_snprintf_show (kernel/bpf/btf.c:8321)
bpf_snprintf_btf (kernel/trace/bpf_trace.c:1047)
bpf_prog_test_run_raw_tp (net/bpf/test_run.c:829)
__sys_bpf (kernel/bpf/syscall.c:4804)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
</TASK>
Fall back to btf_df_show() when the resolved type has no show op; it
emits the "<unsupported kind:N>" placeholder already used for kinds like
FWD and FUNC. bpf_snprintf_btf() then returns the length as usual. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject key-less BTF for hash maps
map_check_btf() allows a key-less BTF (btf_key_type_id == 0) only for
maps that have a ->map_check_btf callback, and leaves the actual
decision to that callback. Hash maps used to have no ->map_check_btf,
so a key-less BTF was rejected outright.
That changed when htab and rhtab gained a ->map_check_btf to register a
dtor - htab in commit 1df97a7453ee ("bpf: Register dtor for freeing
special fields") and rhtab in commit 6905f8601298 ("bpf: Allow special
fields in resizable hashtab"). Neither looks at the key, so a key-less
hash map now passes map_check_btf() and gets created. Reading it back
through bpffs feeds the key type_id 0 into btf_type_seq_show();
btf_type_by_id() returns the void type, kind_ops[BTF_KIND_UNKN] is NULL,
and btf_type_show() dereferences it:
RIP: 0010:btf_type_show+0x223/0x2e0 kernel/bpf/btf.c:8232
RSP: 0018:ffffc9000399f868 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000005 RSI: 0000000000000000 RDI: 0000000000000028
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: ffffc9000399f970 R11: 0000000000000001 R12: ffffffff9b96b140
R13: ffffc9000399f8e0 R14: ffff88803d393c00 R15: 0000000000000003
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000200000000000 CR3: 000000003d213000 CR4: 0000000000352ef0
DR0: 0000000039ae8f55 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
btf_type_seq_show_flags+0xca/0x120 kernel/bpf/btf.c:8250
htab_map_seq_show_elem+0x12e/0x350 kernel/bpf/hashtab.c:1669
map_seq_show+0x13d/0x1e0 kernel/bpf/inode.c:293
traverse.part.0.constprop.0+0x107/0x650 fs/seq_file.c:112
traverse fs/seq_file.c:99 [inline]
seq_read_iter+0x93f/0x1270 fs/seq_file.c:196
seq_read+0x344/0x4d0 fs/seq_file.c:163
vfs_read+0x1e4/0xb40 fs/read_write.c:572
ksys_pread64 fs/read_write.c:764 [inline]
__do_sys_pread64 fs/read_write.c:772 [inline]
__se_sys_pread64 fs/read_write.c:769 [inline]
__x64_sys_pread64+0x1eb/0x250 fs/read_write.c:769
do_syscall_x64 arch/x86/entry/syscall_64.c:61 [inline]
do_syscall_64+0x123/0x790 arch/x86/entry/syscall_64.c:84
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Reject a key-less BTF in htab_map_check_btf() and rhtab_map_check_btf(),
restoring the previous behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: caiaq: Fix potential double-free at error path
The fix for caiaq driver's resource management to handle the errors
tries to release the resources in a common destructor call, but as a
sashiko review for another patch suggested, some of the audio
resources such as URBs have been already freed, and this may lead to a
double-free.
For addressing the double-free, call the common destructor function
from each place, and assure that the resource pointers get cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
net: Remove conflicting altnames for dying netns in __dev_change_net_namespace().
syzbot reported the warning in cfg80211_pernet_exit(). [0]
The repro does the following:
1. create two device in root netns and non-root netns
2. assign the same altname for the two devices
3. remove the non-root netns
Since commit 7663d522099e ("net: check for altname conflicts
when changing netdev's netns"), cfg80211_switch_netns() and
cfg802154_switch_netns() fail if init_net has a device with the
conflicting altname.
default_device_exit_net() had the same issue and commit d09486a04f5d
("net: fix removing a namespace with conflicting altnames") fixed it.
cfg80211_pernet_exit() and cfg802154_pernet_exit() need the same fix.
Let's generalise the fix by removing conflicting altnames for dying
netns in __dev_change_net_namespace().
[0]:
cfg80211_switch_netns(rdev, &init_net)
WARNING: net/wireless/core.c:1871 at cfg80211_pernet_exit+0xd5/0x120 net/wireless/core.c:1871, CPU#1: kworker/u8:9/1160
Modules linked in:
CPU: 1 UID: 0 PID: 1160 Comm: kworker/u8:9 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/24/2026
Workqueue: netns cleanup_net
RIP: 0010:cfg80211_pernet_exit+0xd5/0x120 net/wireless/core.c:1871
Code: e8 03 42 80 3c 20 00 74 08 4c 89 f7 e8 b4 ef 0e f7 4d 8b 36 49 81 fe 20 10 4a 90 74 12 e8 03 3d 9f f6 eb 85 e8 fc 3c 9f f6 90 <0f> 0b 90 eb cc e8 f1 3c 9f f6 eb 05 e8 ea 3c 9f f6 5b 41 5c 41 5e
RSP: 0018:ffffc900057a78f0 EFLAGS: 00010293
RAX: ffffffff8b287154 RBX: ffff88807ba72780 RCX: ffff8880213e8000
RDX: 0000000000000000 RSI: 00000000ffffffef RDI: 0000000000000000
RBP: 00000000ffffffef R08: ffffffff9024cc67 R09: 0000000000000000
R10: fffff52000af4eb0 R11: fffffbfff204998d R12: dffffc0000000000
R13: ffffffff904a1080 R14: ffff888144ed0008 R15: ffff888144ed0e20
FS: 0000000000000000(0000) GS:ffff888124de6000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005642de0a8a70 CR3: 000000007a40c000 CR4: 00000000003526f0
Call Trace:
<TASK>
ops_exit_list net/core/net_namespace.c:200 [inline]
ops_undo_list+0x43d/0x8d0 net/core/net_namespace.c:253
cleanup_net+0x572/0x810 net/core/net_namespace.c:706
process_one_work kernel/workqueue.c:3387 [inline]
process_scheduled_works+0xc3d/0x1630 kernel/workqueue.c:3470
worker_thread+0xa47/0xfb0 kernel/workqueue.c:3551
kthread+0x38b/0x480 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: do not clear curr_active_slave prematurely when releasing all slaves
When releasing all slaves during bond destruction (all == true),
__bond_release_one() unconditionally clears bond->curr_active_slave to
NULL in every iteration.
If a backup slave is released before the active slave,
bond_alb_deinit_slave() triggers rlb_teach_disabled_mac_on_primary(),
which increments the active slave dev promiscuity counter and sets
bond_info->primary_is_promisc = 1.
Because bond->curr_active_slave was prematurely cleared to NULL when
releasing the backup slave, the subsequent iteration releasing the active
slave evaluates oldcurrent as NULL, so bond_change_active_slave(bond, NULL)
is skipped. Consequently, bond_alb_handle_active_change() is never called
to decrement the promiscuity counter, permanently leaking promiscuous
mode on the physical device after bond teardown.
When oldcurrent == slave, bond_change_active_slave(bond, NULL) already sets
bond->curr_active_slave to NULL. We only need to avoid selecting a new
active slave when all == true. Replace the if (all) branch with
if (!all && oldcurrent == slave). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: reject BPF_PSEUDO_FUNC reference to the main program
fixups.c:jit_subprogs() rewrites BPF_PSEUDO_FUNC loads to contain real
function addresses. This function is invoked from bpf_jit_subprogs()
only when env->subprog_cnt > 1. Meaning that for any program like
below:
int main(void *ctx) {
void *ptr = main;
...
bpf_timer_set_callback(..., ptr);
...
}
The 'ptr' won't be ever converted to contain an address.
In combination with e.g. bpf_timer_set_callback() this would lead to a
function call at a bogus address.
Instead of complicating the implementation, just assume that no useful
program needs main to be a sync or async callback and reject
BPF_PSEUDO_FUNC loads for the main subprogram. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/probes: Fix use-after-free on field name/type of events with multiple probes
The fields of a probe-based dynamic event (kprobe, uprobe, eprobe and
fprobe events) are created in traceprobe_define_arg_fields() by handing
the probe_arg name/type strings to trace_define_field(), which only
stores the pointers without copying. Those strings are owned by the
trace_probe and are freed when that probe is removed.
An event can have several probes attached. The field list is defined
only once, by the first probe that registers the event, but it is kept
alive by any surviving sibling probe. Deleting just that first probe by
symbol -
# primary A: fields are defined from A's args
echo 'p:kprobes/ev vfs_read a1=$arg1' > kprobe_events
# append B: shares A's event call
echo 'p:kprobes/ev vfs_write a1=$arg1' >> kprobe_events
# delete only A (matched by symbol), B survives
echo '-:kprobes/ev vfs_read' >> kprobe_events
frees A's args (trace_probe_cleanup() -> traceprobe_free_probe_arg()),
but trace_probe_unlink() keeps the trace_probe_event because the probe
list is not empty. The event call stays registered via B while its
fields now reference freed memory. Any field lookup then reads it, e.g.
echo 'a1 == 1' > events/kprobes/ev/filter
BUG: KASAN: slab-use-after-free in strcmp+0xa7/0xb0
Call Trace:
strcmp
trace_find_event_field
parse_pred
process_preds
create_filter
apply_event_filter
event_filter_write
field->name references parg->name (kstrdup'd, freed with the probe) and,
for array arguments, field->type references parg->fmt (kmalloc'd, freed
with the probe) - the scalar type otherwise points at the static
fmttype rodata, which is safe.
Have traceprobe_define_arg_fields() duplicate the name and type strings
and anchor the copies on the trace_probe_event, which embeds the event
call and outlives every individual probe; trace_probe_event_free()
releases them.
The reproducer above triggers reliably; the field lookup and the delete
both run under event_mutex, so this is a dangling reference after
removal rather than a race.
The issue was found by the autokbug dynamic kernel fuzzer at Tencent
Yunding Lab. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: asymmetric_keys - fix OOB read in pefile_digest_pe_contents
pefile_digest_pe_contents() computes the trailing-data hash length as
pelen - (hashed_bytes + certs_size). A crafted PE can make the addition
exceed pelen, causing the unsigned subtraction to underflow to ~4 GiB.
This is passed to crypto_shash_update() which reads out of bounds and
panics on unmapped vmalloc guard pages.
BUG: unable to handle page fault for address: ffffc900038d8000
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:sha256_blocks_generic (lib/crypto/sha256.c:152)
Call Trace:
<TASK>
__sha256_update (lib/crypto/sha256.c:208)
crypto_sha256_update (crypto/sha256.c:142)
verify_pefile_signature (crypto/asymmetric_keys/verify_pefile.c:436)
kexec_kernel_verify_pe_sig (kernel/kexec_file.c:151)
__do_sys_kexec_file_load (kernel/kexec_file.c:406)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
</TASK>
Kernel panic - not syncing: Fatal exception
Validate that the addition does not overflow and the result does not
exceed pelen before the subtraction. Return -ELIBBAD on failure. |