| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: line6: Reject capture buffers smaller than two packets
line6_capture_copy() splits the copy into the ALSA ring buffer once at
the buffer end and wraps pos_done once, which is only correct when one
packet holds at most buffer_size frames. The packet size comes from the
device's endpoint, and the per-device hw structs allow 64-byte periods
with periods_min 1, so a packet can be larger than the whole buffer.
audio_in_callback() logs an oversized packet and then copies it anyway.
The packet size is known at probe time, so constrain
SNDRV_PCM_HW_PARAM_BUFFER_BYTES in snd_line6_capture_open() to at least
twice the larger of the two endpoints' packet sizes. Two rather than
one, because pos_done advances by the packet and wraps once, so a buffer
of exactly one packet leaves the position unchanged after every packet.
hw_params then rejects a buffer that cannot hold two packets, and the
single wrap is valid for every configuration that gets through. Keep a
guard in line6_capture_copy() that drops an oversized packet with a
ratelimited error, for the case that should no longer be reachable.
Reproduced on 7.3-rc7 with a USB/IP device presenting the GuitarPort
interface layout and 1024-byte packets into a 128-byte buffer: ALSA
logged "invalid position: pos = 224, buffer size = 32" and the driver
logged "driver bug: len" on every following packet. With this patch a
1024-byte buffer is refused at hw_params, and a 2048-byte buffer streams
for 30 s with no report and with the position moving inside the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/tas2781: Only accept CRC-less V1 data if all entries are valid
Commit 408249089c48 ("ALSA: hda/tas2781: Accept V1 calibration data
without CRC") only checked the first device entry. On machines where
the BIOS populates fewer entries than p->ndev, the remaining all-zero
entries are applied and tas2781_cali_preproc() divides by zero on
playback open.
Accept CRC-less V1 data only if every expected entry is non-zero and
self-consistent (R0 * 1/R0 close to 1.0), otherwise reject it as
before. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: cs46xx: Handle SCB creation failures before dereferencing
With CONFIG_PM_SLEEP enabled, cs46xx_dsp_create_scb() can return NULL
if kmemdup() fails to allocate the SCB data saved for resume.
cs46xx_dsp_scb_and_task_init() and _dsp_create_generic_scb() dereference
the returned pointer without checking it, causing a NULL pointer
dereference on allocation failure.
Check both return values before accessing the SCB descriptors.
Return -ENOMEM when creating the null SCB fails and propagate NULL
from _dsp_create_generic_scb().
Found by Linux Verification Center (linuxtesting.org) with SVACE
static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau/nvkm: clear use.enabled when subdev init fails
On Kepler boards without the video decode falcon firmware installed
(msvld/mspdec/msppp), every other VA-API decode attempt binds to an
engine with no ucode loaded. The submitted work never completes, which
leads to a context switch timeout, a channel recovery that cannot reset
the engine, and eviction waits on fences that never signal. The process
ends up stuck in D state, or killed by SIGBUS when it touches a buffer
evicted after the wait times out:
msvld: unable to load firmware data
msvld: init failed, -19
fifo: SCHED_ERROR 0a [CTXSW_TIMEOUT]
vo[5444]: channel 14 killed!
WARNING: drivers/gpu/drm/nouveau/nvkm/engine/fifo/runl.c:117 at nvkm_runl_rc+0x2a4/0x3b0 [nouveau]
[TTM] Buffer eviction failed
WARNING: drivers/gpu/drm/nouveau/nouveau_bo.c:1092 at nouveau_bo_move_ntfy.part.0+0x9b/0x100 [nouveau]
Tracing nvkm_subdev_ref() and nvkm_subdev_init_() shows the pattern:
a reference taken with enabled=0 runs nvkm_falcon_init(), which
returns -ENODEV; the next reference sees enabled=1 and succeeds
without running it.
Clear use.enabled when init() fails, so that every later reference
retries init and fails cleanly. The other readers of use.enabled are
fini() handlers that use it to skip teardown, which they now also do
after a failed init().
On a GK107 (Quadro K1100M) without video firmware, playing H.264 with
mpv --hwdec=auto: without this patch the GPU channel is killed within a
minute and mpv hangs; with it, VA-API decoder creation fails, mpv falls
back to software decoding, and no faults are logged. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: mm: validate /dev/mem mmap ranges without overflow
An arm64 syzkaller reproducer creates a FUSE character device with
major:minor 1:1, so opening it uses the /dev/mem file operations. It
maps one page from offset 0xfffffffffffff000 at user address zero.
The next openat() with a NULL pathname triggers a synchronous external
abort (SEA, ESR 0x96000010) in strncpy_from_user() via do_getname(),
panicking the kernel.
valid_mmap_phys_addr_range() checks the exclusive end by adding the
mapping size to the starting address. For this offset, the sum wraps
to zero and passes the PHYS_MASK test, allowing an out-of-range PFN to
reach remap_pfn_range(). The inclusive-end overflow check in
mmap_mem_prepare() does not catch it because the end is ULONG_MAX.
Reject starting PFNs outside PHYS_MASK and compare the inclusive length
against the remaining physical range without overflowing. This also
allows mappings that end exactly at PHYS_MASK, which the old check
incorrectly rejects.
[catalin.marinas@arm.com: changed the check to look more like __access_ok()] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: don't drop the gang dependency fence twice
drm_sched_job_add_dependency() drops the fence reference when it fails,
but amdgpu_cs_submit() drops it again, so the scheduled fence of a gang
member loses a reference it still needs.
A GFX+COMPUTE gang waiting for another context, with the
xarray node allocation for the leader's dependency failed through
failslab:
WARNING: drivers/dma-buf/dma-fence.c:589 at dma_fence_release+0x34d/0x730, CPU#1: amd_uapi_regres/2993
drm_sched_job_cleanup+0x2c2/0x340 [gpu_sched]
amdgpu_job_free+0xcb/0x3e0 [amdgpu]
amdgpu_cs_parser_fini+0x435/0x710 [amdgpu]
amdgpu_cs_ioctl+0xcd2/0x7a60 [amdgpu]
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:dma_fence_signal_timestamp_locked+0x1b8/0x610
(cherry picked from commit 5aa070a83c8378810b906cc8bfc650ce69822a7c) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: don't walk the CS chunks when allocating them failed
amdgpu_cs_pass1() sets p->nchunks before allocating p->chunks, and the
allocation failure path skips resetting it. amdgpu_cs_parser_fini() then
frees the kdata of nchunks chunks from a NULL array. On navi48 with the
chunk array allocation failed through failslab:
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:amdgpu_cs_parser_fini+0x35d/0x710 [amdgpu]
amdgpu_cs_ioctl+0xcae/0x7a20 [amdgpu]
drm_ioctl_kernel+0x180/0x320 [drm]
Set nchunks once the array exists.
(cherry picked from commit 0c828445757b86aaa3ed2638832d76f450022bdf) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: drop the dma-buf reference when a KFD import fails
import_obj_create() takes a reference on the dma-buf for the new kgd_mem,
but the error path after validating the BO doesn't drop it. Since the
validation reserves the BO interruptibly, an import failing with
-ERESTARTSYS leaks the exported BO with its memory, and keeps the module
in use.
Importing a 64 MiB VRAM BO in a loop while getting SIGUSR1
every 20 us and another thread changes the BO's mappings:
INFO: 171821 imports, VRAM used before 65 MiB, after 129 MiB
modprobe: FATAL: Module amdgpu is in use.
Drop the reference, and free the sync object and the mutex of the kgd_mem
as well. With that VRAM usage returns to 65 MiB after the same test.
(cherry picked from commit b4d1eca2729840148ff2ea957724ce764ca5a94e) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Report MES ring wait timeouts.
Return -ETIMEDOUT when the fence wait before submission expires instead
of reporting success without submitting the packet.
(cherry picked from commit 34341594a87b4a3f28be41e3e70a4787f02b3d9e) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix duplicate dependency fence releases
drm_sched_job_add_dependency() consumes its fence reference on success
and failure. Do not release the fence again if
drm_sched_job_add_dependency() fails.
(cherry picked from commit e04f3dfb2071451633e6440a3911a9bb65df9144) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix NULL deref in dcn401_update_clocks_update_dtb_dto
[Why]
resource_get_otg_master_for_stream() can return NULL if no OTG master pipe
is found for a given stream. The current code dereferences this pointer
without a NULL check. This may lead to a possible NULL pointer
dereference.
[How]
Add an explicit NULL check and skip the stream if the OTG master is not
found. This is similar to dcn60_update_clocks_update_dtb_dto().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
(cherry picked from commit ffde3d74c1faeeb645b66d02d02fdae3e073941b) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx12: disallow GFXOFF while updating the SPM VMID
gfx_v12_0_update_spm_vmid() does a read-modify-write of RLC_SPM_MC_CNTL
over MMIO without keeping GFX powered, unlike gfx11. When GFX is in
GFXOFF at that point the update doesn't stick, and with the SPM VMID
programmed on submission again, the job of a process with a reserved
VMID can still run with the SPM writing through VMID 0.
On navi48, after a few other submissions and a VM fault on the same VM,
a COPY_DATA of RLC_SPM_MC_CNTL from such a job reads 0 although the
update was called for it:
$ amd_uapi_regression --run-subtest cs-secure-ib-compute,gem-mapping-info-high-va,gpuvm-fault-high-va,reserved-vmid-spm-vmid
amdgpu 0000:03:00.0: [gfxhub] page fault (src_id:0 ring:40 vmid:7 pasid:185)
amdgpu 0000:03:00.0: Faulty UTCL2 client ID: SDMA1 (0xe)
RLC_SPM_MC_CNTL in the job: 0x00000000
With GFXOFF disallowed around the update it reads the reserved VMID 15.
(cherry picked from commit 907aebc5578ae09fa5c0e2f0784201295837e60b) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: clear RB_OVERFLOW bit when enabling interrupts for navi10_ih
Port this change to navi10_ih.c:
commit afbf7955ff01 ("drm/amdgpu: clear RB_OVERFLOW bit when enabling interrupts")
Setting IH_RB_WPTR to 0 does not clear RB_OVERFLOW if RB_ENABLE is not
set. Pulse WPTR_OVERFLOW_CLEAR after RB_ENABLE (and with
WPTR_OVERFLOW_ENABLE) so overflow is cleared when interrupts are
enabled.
(cherry picked from commit 713fb4ab04f4d2af6120f8eb607c5673b2759b38) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: validate the moved individual BOs on restore
An individual BO of a user queue VM, i.e. one which doesn't share the
root reservation, goes to the individual needs_update list when it is
evicted. The user queue restore looked at vm->invalidated for them, which
the VM state machine rework turned into the always_valid evicted list and
commit 18decfc9e8cc ("drm/amdgpu/userq: actually validate userq BOs")
into the individual evicted one. That list only holds imported DMA-bufs of
compute VMs though, so for a user queue VM nothing is validated.
The restore then neither locks such a BO nor moves it back. Its PTEs are
updated to wherever it is now, cleared if it went to system memory, and
it doesn't get the new eviction fence, so it can move again under the
running queue.
On navi48, once the BOs of an SDMA user queue are evicted from GTT
(debugfs amdgpu_evict_gtt) the queue faults on its ring and rptr:
amdgpu 0000:03:00.0: in page starting at address 0x0000000100000000 from client 10
amdgpu 0000:03:00.0: Faulty UTCL2 client ID: SDMA0 (0xd)
amdgpu 0000:03:00.0: in page starting at address 0x0000000100101000 from client 10
Validate the BOs on the individual needs_update list like before.
(cherry picked from commit eb0d94765d4be18d41e93ad09947dd9cc06ed31a) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: check amdgpu_vm_ready() in dma-buf move notify
amdgpu_dma_buf_move_notify() touches the page tables without first
calling amdgpu_vm_ready(). When a process is SIGKILLed, its VM entities
are stopped. Teardown of an imported dma-buf then tries to clear PTEs by
submitting to one of those stopped entities. That eventually hangs the
task.
Commit aa5fc4362fac ("drm/amdgpu: fix task hang from failed job
submission during process kill") added the stopped entity check in
amdgpu_vm_ready() and used it in amdgpu_cs_vm_handling(). That did not
cover a call in amdgpu_dma_buf_move_notify(), what was already mentioned
in:
https://lists.freedesktop.org/archives/amd-gfx/2025-October/133076.html
Tested by SIGKILLing a GPU workload holding imported dma-bufs. Without
the patch "Trying to push to a killed entity" errors are logged, then a
task hangs. With the patch there are no hung tasks. This was tested on a
6.18 kernel.
(cherry picked from commit bee5c9d7a34cb1b510ad3b4c18c30f9d38b0ab7d) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: keep the CS user fence BO in GTT
The CS ioctl hands the GPU the GART address of the user fence BO, but
since the BO keeps its own preferred and allowed domains, it no longer
makes sure the BO is in GTT. A user fence in a VRAM BO, which only needs
to be a page in size, gets its address from amdgpu_bo_gpu_offset(), which
warns about non-contiguous VRAM. On navi31, a CS with a user fence in a
4K VRAM BO, or in one created with AMDGPU_GEM_CREATE_VM_ALWAYS_VALID:
WARNING: amdgpu_object.c:1531 at amdgpu_bo_gpu_offset+0x86/0xb0 [amdgpu], CPU#11: cs_gem_checks/18393
RIP: 0010:amdgpu_bo_gpu_offset+0x86/0xb0 [amdgpu]
Call Trace:
<TASK>
amdgpu_cs_parser_bos.isra.0+0x4eb/0x850 [amdgpu]
amdgpu_cs_ioctl+0x97e/0x2510 [amdgpu]
drm_ioctl_kernel+0xac/0x110 [drm]
drm_ioctl+0x2c6/0x5b0 [drm]
__x64_sys_ioctl+0xa0/0xf0
do_syscall_64+0xa3/0x4d0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
and BOs which can't be in GTT at all, like GWS or OA ones of a page in
size, pass the checks as well.
Only take BOs which can't be anywhere else than in GTT as user fence,
which the CS then validates there along with its other BOs. While at it,
detect userptrs with amdgpu_ttm_tt_is_userptr(); amdgpu_ttm_tt_get_usermm()
returns NULL once the task which created the userptr is gone.
v2: only take BOs which can only be in GTT instead of special casing the
user fence BO in the validation, use amdgpu_ttm_tt_is_userptr()
(Christian)
(cherry picked from commit f16989def9561d04d0f2e77216f5319112d29bf1) |
| In the Linux kernel, the following vulnerability has been resolved:
net: reject a negative TCP header offset in qdisc_pkt_len_segs_init()
qdisc_pkt_len_segs_init() stores skb_transport_offset(), or the inner
offset, in the unsigned hdr_len. A header in front of skb->data gives a
negative offset. For an offset a little below zero, pskb_may_pull() gets a
small length and succeeds. Then a 64-bit kernel reads the TCP header far
after the skb and can crash. Further below zero pskb_may_pull() fails.
Commit 28a57fb2c5df ("net: iptunnel: fix stale transport header during
tunnel decapsulation") fixed one source of such offsets. Other code that
removes bytes from the front of a packet can leave the same stale header.
Return SKB_DROP_REASON_SKB_BAD_GSO for a negative offset in the TCP branch.
SKB_GSO_UDP_L4 and the other GSO types read no header and still get a wrong
qdisc_pkt_len(). On a 64-bit kernel only packets that cause the read after
the skb today get a new result. Then __dev_queue_xmit() drops them and
returns -EINVAL, but sch_handle_ingress() ignores the result. Their content
can be valid. Thus the code that leaves the header stale needs its own fix. |
| In the Linux kernel, the following vulnerability has been resolved:
ovl: inherit FMODE_NONOTIFY when opening directory realfiles
When fanotify hands a listener an fd for a permission event on an
overlay directory, ovl_dir_open_realfile() opens the real directory via
dentry_open(), not backing_file_open(), so the lower open could still
raise FS_OPEN_PERM and deadlock a listener that also marks the backing
filesystem.
Export dentry_open_nonotify() and call it from ovl_path_open_realfile()
when the overlay user file must not generate events. Ordinary
ovl_path_open() callers are unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: fix unmap_mapping_range() beyond 4 GiB on 32-bit
Commit 9eab0421fa94 ("mm: fix unmap_mapping_range high bits shift bug")
made holebegin and holelen unsigned before they are shifted, by casting
them to pgoff_t. That is an unsigned long: on a 32-bit kernel the cast
cuts off the upper half of the two loff_t values, so a hole which begins
at 4 GiB or beyond is taken for one in the first 4 GiB of the file.
truncate_pagecache() passes the new size of the file and asks for private
COWed pages to be unmapped as well. If a file of 6 GiB is truncated to
5 GiB, everything from 1 GiB on is unmapped, and what a process has
written to a private mapping of the range between 1 GiB and 5 GiB is
lost: it reads the contents of the file again.
Where the range has an end, the wrong range is unmapped instead of the
right one. The page cache copes with that, as it unmaps every folio that
it removes. The callers which only have unmap_mapping_range() to get
rid of user mappings do not, for example drm_vma_node_unmap(), whose fake
offsets reach beyond 4 GiB on 32-bit, and revoke_iomem() with physical
addresses of more than 32 bits.
Cast to u64 instead. Nothing changes for 64-bit kernels.
Fix generated by an LLM and sent by Josef Bacik in private. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memory: reject remote COW faults on PFN mappings
When handling a COW fault without a normal source page (PFN mappings),
__wp_page_copy_user() copies from the faulting user address. For remote
faults, this accesses the wrong address space, resulting in wrong data
getting copied.
For example, user_events updates an enable bit in the registering
process's memory. If that memory needs to be faulted in,
user_event_enabler_fault_fixup() calls fixup_user_fault() from a work
item. Placing the enable bit in a private PFN mapping can trigger this
remote COW path.
Reject these faults with VM_FAULT_SIGBUS when the target mm differs from
current->mm: remote faults. Ordinary (non-PFN) mappings are not affected.
The user-address copy dates back to commit 6aab341e0a28 ("mm: re-architect
the VM_UNPAGED logic"); likely, actual ways to get remote faults in
there on COW PFN mappings appeared afterwards. But the fix is simple and
straight forward.
Fix generated by an LLM and sent by Chris Mason in private.
[ david: simplify comment and description ] |